railroad.wikisort.org - Train

The Indian locomotive class WAM-4 is a class of 25 kV AC electric locomotives that was developed in 1970 by Chittaranjan Locomotive Works for Indian Railways. The model name stands for broad gauge (W), alternating current (A), mixed traffic (M) engine, 4th generation (4). They entered service in March 1971. A total of 500 WAM-4 were built at CLW between 1970 and 1983, which made them the most numerous class of mainline electric locomotive till its successor the WAG-5.

WAM-4
Arakkonam based WAM-4 at Perambur
Type and origin Power type Electric Designer RDSO Builder CLW Build date 1970–1983 Total produced WAM-4: 500 WAG-5: 53 Rebuilder CLW Rebuild date 1978–1983 to WAG-5 Number rebuilt 53
Specifications Configuration: ​  • AAR C-C  • UIC Co′Co′  • Commonwealth Co+Co Gauge 5 ft 6 in (1,676 mm) Bogies ALCO Asymmetric cast frame trimount Wheel diameter New: 1,092 mm (3 ft 7 in) Half worn: 1,055 mm (3 ft 5+1⁄2 in) Full worn: 1,016 mm (3 ft 4 in) Wheelbase 2,108 mm (6 ft 11 in) Length: ​  • Over couplers 19,975 mm (65 ft 6 in)  • Body 18,680 mm (61 ft 3 in) Width 3,055 mm (10 ft 0 in) Height 4,162 mm (13 ft 8 in) Frame type Asymmetric cast frame Axle load 18.8 tonnes (18.5 long tons; 20.7 short tons) Loco weight 112.8 tonnes (111.0 long tons; 124.3 short tons) Sandbox cap. 16 units X 30 t (30 long tons; 33 short tons) Power supply 110 V DC Supply Electric system/s 25 kV 50 Hz AC Overhead Current pickup(s) Pantograph Generator HEIL BOT 3460 A Traction motors Alstom TAO 659A1  • Rating 1 hour 770 HP. 750 V, 840 A, 1095 RPM  • Continuous 798 HP. 750 V, 870 A, 1070 RPM Head end power 110 V DC Supply Transmission Electrical Gear ratio 15:62 MU working 4 units Loco brake Air, Rheostatic braking Train brakes Air, Vacuum and Dual Safety systems Slip control, Over voltage relay, No volt relay, Earth fault relay, Low pressure governor, Train parting alarms, and Brake cylinder cutoff valve
Performance figures Maximum speed 120 km/h (75 mph) Power output 3,640 hp (2,710 kW) Tractive effort: ​  • Starting 33,840 kgf (331.9 kN; 74,600 lbf)  • 1 hour 30,000 kgf (290 kN; 66,000 lbf)  • Continuous 17,600 kgf (173 kN; 39,000 lbf)
Career Operators Indian Railways Class WAM-4 Numbers WAM-4B: 20400–20699, 21200–21399 WAG-5: 21100-21138 Nicknames Garuda, Ananth, RAJATABHA, Surubhi, Navchetna, Sukh Sagar, Naveen Locale All over India Delivered 4 December 1970 First run March 1971; 51 years ago (1971-03) Preserved 6 units Disposition A few units still in inferior service, rest scrapped

The WAM-4 is one of the most successful locomotives of Indian Railways having served both passenger and freight trains for over 51 years. This class provided the basic design for a number of other locomotives like WCAM-1, WAG-5A, WCG-2, and some WAP-1 models. However, with the advent of new 3-phase locomotives like WAP-5 and WAP-7, the WAM-4 locomotives were relegated to hauling smaller passenger trains and now the aging fleet of WAM-4 locomotives are being rapidly scrapped and have been fully withdrawn from mainline duties.

History

Origins

In the 1970s, the Indian Railways started a series of study projects for a high horsepower locomotive. Although the WAG-1/WAG-4 was being introduced, officials believed that a much larger and more capable locomotive was needed, especially to haul Freight trains that was heavy for any existing locomotives. These studies led to initial requirements for an locomotive with a tractive effort of 33,840 kgf (331.9 kN; 74,600 lbf) and a speed of 120 km/h (75 mph).The WAM-4 was conceived while goods traffic was increasing in the 1970s. The era of Co-Co locomotives, led by the enormous popularity of the WDM-2, had revolutionized long-distance travel. With the aim of addressing the shortcomings of the previous WAM-1/2 and WAG-1, WAG-2, WAG-3, WAG-4 classes and remove steam locomotives from IR by a target date of 1990. The WAM-1s were not great successes as some of their advanced features were unsuitable for Indian conditions.

so the designers at RDSO and CLW decided to use the following

• Instead of the Bo-Bo bogies of WAM-1/2, ALCO asymmetric Trimount bogies of the WDM-2 were provided for better traction and power.
• Silicon rectifiers with speed control by three series-parallel motor combinations and weak field operation.
• Auxiliaries from Westinghouse and Kirloskar (compressors), S F India (blowers) and Northey (exhauster)
• Air brakes for loco and vacuum train brakes fitted as original equipment with Rheostatic braking also provided
• MU operation made possible up to 4 units possible.

Production

Production of these locomotives started in 1970 with #20400 and exactly 500 WAM-4s were built in 13 years with #21399 “Anant” being the last one. Production ended on August 3 1983. WAM-4 though an indigenously produced loco was heavily inspired by French box design and naturally favoured a French TM which was the Alstom made TAO TM. A single WAM-4 can generally haul up to a 24-coach passenger rake. This class proved so successful by virtue of its ruggedness suitable for Indian conditions and simplicity of maintenance. In January 2020, the last WAM-4 units (four from Tata ELS) were withdrawn from mainline service.[1][2] Currently 8 locomotives are currently doing shunting and departmental works.

Rebuilding

A number of locomotives were rebuilt as WAM-4B in the late 1970s to evaluate Alstom TAO 659 Traction Motors and for exclusive use on freight duties. These 'locos' were ballasted to improve traction and had excellent load-hauling capabilities, This experiment gave rise to the future WAG-5 locos.[3]

Duties

The class was designed for both passenger and freight work. Many of the original locomotives were fitted with vacuum brakes only. With the withdrawal of many WAG-1 and WAM-1 locomotives in the 1990s, the WAM-4 units were given air brakes to prolong their life into the 1990s and beyond.

Sub-classes

This loco class has been seen in many variations, as a lot of workshops and sheds have carried out their own enhancements or modifications to the basic loco design. Although the code indicates a mixed-use loco, most WAM-4's ended up hauling passenger trains.

Variants include

• WAM4B or G: Freight only (re geared version)
• WAM4D or DB: Dual Braked (Air and Vacuum)
• WAM4E: Air Brake only (for both loco and train)
• WAM4H: Hitachi Traction Motors instead of Alstom
• WAM4P: Passenger only (re geared version)
• WAM4/2S3P: 2 Traction Motors in Series, 3 in Parallel
• WAM4/6P: 6 traction motors permanently in parallel
• WAM4/6PE: Air braked, 6 Traction Motors perm. in parallel
• WAM4/6PDBHS: 6 Traction Motors permanently in parallel, Dual Brakes, High Speed
• WAM-4P D: Passenger only (dual brakes)
• WAM-4P DB 6P and WAM-4 6P D: These are for superfast trains
• WAM-4P DB 3P and WAM-4 2S-3P: some superfasts, passengers

The 'DB' or 'D' generally, but perhaps not always, indicates dual-brake capability. 'HS' may be for 'high speed'.'2S', '3P', '6P', etc. indicate traction motors connected in series or parallel. The WAM-4 has six traction motors, and originally they were wired to be available in different configurations at different power settings. At notches up to 14, all motors were in series (at notch 14 all resistors dropping out); up to notch 21 in series-parallel combinations (three pairs of motors in series, the pairs themselves being in parallel); and further notches with all motors in parallel (at notch 30 all motors are in parallel with resistors dropping out). This is the original configuration of the WCAM-1 series of locomotives too.

The WAM-4 locomotives were later reconfigured to have all motors always in parallel (6P variants) or with the three series-connected pairs in parallel (2S 3P variants). Some WAM-4 locomotives from CLW are thought to have had the 2S 3P configuration right from the start. The 2S 3P configuration was better for the mixed traffic loads especially as it allowed the locomotives to start hauling larger loads without stalling. With increasing use of the WAM-4 locomotives for passenger traffic the all-parallel configuration was deemed more desirable since it allowed higher speeds and higher acceleration.

Livery

This loco has the widest variety of liveries, with each loco shed having its own livery

Most of the WAM-4 locomotives now have their MU capability disabled as RDSO disapproves of these locomotives running MU'd over 100 km/h. [4]

Named locomotives

A few WAM-4 locomotives have been named by Indian Railways[5]

List of Named locomotives

Class	Loco Number	Name	Loco Shed	Current status	ref
WAM-4	20401	Rajatabha	Bhillai [BIA]	Condemned [07/08/2007]	[6]
WAM-4	20420	Sukh Sagar Naveen	Vijayawada [BZA]	Scrapped	[7]
WAM-4	20615	Surubhi	Asansol [ASN]	Condemned in November 2011	[8]
WAM-4	21320	Garuda	Arakkonam [AJJ]	Plinthed at Rail Soudha, SWR HQ, Hubli [January 2020]	[9]
WAM-4	21380	Navchetna	Asansol [ASN]	In Inferior service	[10]
WAM-4	21399	Anant	Bhusawal [BSL]	The last WAM-4 ever built. No longer in holdings - assumed withdrawn/scrapped [January 2019]	[11]

Preserved Examples

As increasing numbers of WAM-4 have been retired, some have found their way into museums or other uses. A few WAM-4 locomotives have been preserved by Indian Railways at various location around India[12][13]

Class	Loco Number	Previous shed	Name	LIvery	Location	ref
WAM-4	20400	BIA		BIA cream/orange with blue stripe	Used at Electric Loco Training Center, Uslapur [October 2011]. Reumbered ELTC-120	[14]
WAM-4	20472	Ghaziabad (GZB)			Restricted to shunting/departmental duties only. Earmarked for preservation: I.R. Heritage Website [November 2018]	[15]
WAM-4	20484	Bhusawal (BSL)		BSL cream/orange with orange lining	Loco now preserved at CLW loco park	[16][17]
WAM-4	20601	Jhansi (JHS)		Maroon with cream band	Earmarked for preservation: I.R. Heritage Website [November 2018]	[18]
WAM-4	21320	Arakkonam (AJJ)	Garuda	Red/dark grey/light grey with white line	Plinthed at Rail Soudha, SWR HQ, Hubli [January 2020]	[19]
WAG-5/WAM-4B	21101	Tatanagar (TATA)		Indian Tricolour Livery	Plinthed outside TATA	[20]

Locomotive sheds

Zone	Name	Shed Code	Quantity
Eastern Railway	Sealdah	SLSD	3
Northern Railway	Ghaziabad	GZB	1
	Ludhiana	LDH	1
North Central Railway	Kanpur	CNB	3
Total Locomotives Active as of 01-06-2022[21]			8

Former sheds

• Vadodara
• Visakhapatnam
• Itarsi
• Arakkonam
• Mughalsarai
• Lallaguda
• Vijayawada
• Bhusawal
• Valsad
• Howrah
• Jhansi
• Tughlakabad
• Tatanagar
• Bhilai

Technical specifications[4]

Traction Motors	Alstom TAO 659 A1 (575 kW, 750 V). Six motors, axle-hung, nose-suspended, force-ventilated.
Gear Ratio	15:62 originally (and still for WAM-4 2S3P), now many variations, 21:58 being common for WAM-4 6P locomotives.
Transformer	Heil BOT 3460 A, 22.5 kV / 3460 kVA.
Rectifiers	Two silicon rectifier cells, 1270 V / 1000 A each cubicle.
Pantographs	Two Faiveley AM-12.
Hauling capacity	2,010 t (1,980 long tons; 2,220 short tons)
Current Ratings	(WAM-4 6P) 1100A/10min, 750A continuous

Image Gallery

• 
  TATA based WAM-4 in barbie doll livery rest at Durg Jn.
• 
  AJJ based Saptagiri livery WAM-4 rest at Arakkonam Jn.
• 
  AJJ based WAM-4 with an express train
• 
  WAM 4 series loco 20491 from Vadodara Shed VSKP-Nanded Express
• 
  WAM 4 series loco 21226 from Visakhapatnam Shed spotted at Moula Ali
• 
  WAM 4 series loco 21219 from Arakkonam Shed spotted at Visakhapatnam Junction
• 
  13022 (Raxaul - Howrah) Mithila Express with HWH WAM 4 21281 based at katni shed
• 
  WAM-4P loco of Vijayawada Shed spotted at Secunderabad
• 
  WAM 4 with the Malwa Express
• 
  12295 (SBC-PNBE) Sanghamitra Express from Mughalsarai Shed
• 
  Howrah bound 12814 (Tatanagar-Howrah) Steel Express with WAM4 series loco of Tata shed

See also

• Indian Railways
• Locomotives of India
• Rail transport in India

References

Bibliography

• Hughes, Hugh (1996). Indian Locomotives: Part 4 – 1941–1990. Harrow, Middlesex: The Continental Railway Circle. ISBN 0-9521655-1-1. OCLC 35135033.

External links

• Specifications
• India railway fan club

На других языках

---

[de] IR-Klasse WAM-4

Die WAM-4 ist eine Elektrolokomotive der Indian Railways für den Betrieb mit 25-kV-Wechselstrom mit einer Frequenz von 50 Hz, die 1970 von Chittaranjan Locomotive Works (CLW) entwickelt wurde. Die Bezeichnung der Baureihe setzt sich aus W für wide ‚Breitspur‘, A für alternating current ‚Wechselstrom‘ und mixed ‚Universallokomotive für Güter- und Personenverkehr‘ zusammen. Hinter dem Bindestrich folgt eine 4, um die 4. Generation der WAM-Lokomotiven zu kennzeichnen. Zwischen 1978 und 1983 wurden bei den CLW insgesamt 500 WAM-4 gebaut, was sie bis zu ihrem Nachfolger, der WAG-5, zur meistgebauten Baureihe indischer Elektrolokomotiven machte. Die WAM-4 ist eine der erfolgreichsten Lokomotiven der Indian Railways und wird seit 50 Jahren eingesetzt. Die Lokomotive war die Basis für einige andere Baureihen wie die WCAM-1, die WAG-5A, die WCG-2 und einige WAP-Modelle. Mit dem Aufkommen der Lokomotiven mit Drehstromantrieb der Baureihen WAP-5 und WAP-7 wurden die WAM-4 nur noch für die Beförderung untergeordneter Personenzüge genutzt, bevor sie ab 2005 außer Dienst gestellt wurden.

---

- [en] Indian locomotive class WAM-4

---

---